QmtechCycloneIVBoardDemos

1. Project description

A set of additional non-official demo projects for QmTech Cyclone IV Core Board (EP4CE15F23C8).

2. Demos

2.1 Echo+1 RS232 Demo

For testing RS232 QuickRS232 module was designed project SerialPortEcho. This project receive bytes from serial port (COM) that is configured in following mode - 115200 bit/s, 1 stop bit, even parity, no flow control. This project do following: receive byte, add + 1 and send it back.

You could use our application Zerial to work with RS232:

2.1.1 Demo project on board pinout

• CLK - global clock - already on the board -> DIFFCLK_1P (T2)
• RX - RS232 RX line - connected to U8 20 pin -> IO_AB19
• TX - RS232 TX line - connected to U8 22 pin -> IO_AB20
• RTS - we don't USE it in this demo because simple TTL to RS232 converter, but anyway we connect it to U8 24 pin -> IO_Y21
• CTS - we don't USE it in this demo because simple TTL to RS232 converter, but anyway we connect it to U8 26 pin -> IO_W21
• RX_LED - connect it to D5 LED -> DIFFIO_L2P (E4)
• TX_LED - don't have on board free LED, therefore just out it to pin 30 of U8 (IO_U21)

Additionally RS232-to-TTL converter must be attached to power supply line and ground, that also could be taken from U8:

• 3V3 - Any pin from (3, 4)
• GND - Any pin from (1, 2, 61, 62)

2.2 Cmd Decode+Encode RS232 Demo

Usually we don't work with separate bytes, we are interacting with device by commands, device is answering on received command, therefore we wrapped bytes in Command/Answer via frames.

In this demo Frame have a following format of a Frame : SOF | Space | Payload Len | Payload |EOF , where:

• SOF - start of a frame (2 bytes of 0xFF)
• Space - separator (0 Byte - 0x00)
• Payload len - number of payload bytes
• Payload - actual payload, could be up to 255, but in demo restricted to 8
• EOF - end of a frame (2 bytes of EE)

In this demo (SerialPortWithCmdProcessor folder/project) we are having following 2 commands:

1. Set 4-byte register - 0xFF 0xFF 0x00 0x07 0x01 0x02 0x10 0x20 0x30 0x40 0xEE 0xEE which means SET (cmd code 0x01, 0 byte of payload) Register 0x02 (index of registers 0-7, 1 byte of payload) to value 0x10203040.
2. Get 4-byte register - (cmd code 0x02), i.e. reading of register of index 0x03 : 0xFF 0xFF 0x00 0x02 0x02 0x03 0xEE 0xEE

2.2.1 Testbenches diagrams demonstrating how it works:

Example of how decoder works, we haven't yet encoder (maybe will be in future)

Example of interacting with device by Commands/Answers

2.2.2 Demo project on board pinout

• CLK - global clock - already on the board -> DIFFCLK_1P (T2)
• RX - RS232 RX line - connected to U8 20 pin -> IO_AB19
• TX - RS232 TX line - connected to U8 22 pin -> IO_AB20
• RTS - we don't USE it in this demo because simple TTL to RS232 converter, but anyway we connect it to U8 24 pin -> IO_Y21
• CTS - we don't USE it in this demo because simple TTL to RS232 converter, but anyway we connect it to U8 26 pin -> IO_W21
• RX_LED - connect it to D5 LED -> DIFFIO_L2P (E4)
• TX_LED - don't have on board free LED, therefore just out it to pin 30 of U8 (IO_U21)

Additionally RS232-to-TTL converter must be attached to power supply line and ground, that also could be taken from U8:

• 3V3 - Any pin from (3, 4)
• GND - Any pin from (1, 2, 61, 62)

2.3 DRAM Explorer + RS232 Demo

is under development....

Give us a STAR for motivating us to do this (100 stars min to prioritize this work)